Casual Conversation
I miss the days just buying a TV in a shop without worries
akacastor 2 months ago • 100%
For my Samsung 85" TV, entering the wifi password was a requirement - without wifi access, several weeks after installation, the TV stopped displaying video from any input. The only solution was to enter the wifi password, at which point the TV immediately returned to normal operation.
Just because it appears to be optional to connect the device to internet does not mean the basic functionality will work.
[An album of photos from the Cowichan Pride Parade 2024 in Duncan, BC, Vancouver Island.](https://flic.kr/s/aHBqjBwxvZ) https://flic.kr/s/aHBqjBwxvZ 
Ask Electronics
PCB making with laser printer toner
akacastor 4 months ago • 100%
When making PCBs with the toner transfer method, I've used photo paper intended for inkjet printers and printed (mirrored) on it with a laser printer. Then iron the paper (printed side down) onto the PCB. Some pressure is needed but not TOO much or fine traces will squish together. Soak the board with paper stuck to it in water and then the paper can be peeled off, leaving the toner transferred to the copper. Bits of stuck paper can be removed with gentle rubbing in the water with fingers or a soft toothbrush.
If the toner did not transfer well, it can easily be removed by cleaning with acetone, then repeat until successful. Key to getting a good toner transfer is to completely clean the copper first. I scrub with a scotchbrite pad and then clean with acetone and a paper towel, until completely clean and then don't touch the copper with your fingers (greasy greasy fingerprints). Any oils or dirt will make the toner not stick. Some paper is easier to remove from the copper after ironing on - there was a specific Staples SKU (inkjet photo paper in a red box) that I remember being particularly good. I believe the inkjet paper allowed the toner to transfer and release more cleanly, with less pressure and heat required. I also found I got a nice result using the same toner transfer method onto a block of wood (purely aesthetic, not part of a circuit haha).
Some people would use laminator machines to "iron" the toner onto the copper board - I have never tried it that way, but I guess if you get the pressure and heat dialed in it could be pretty consistent. I've had good success using an iron by hand, after a few tries to find good temperature and pressure to apply.
I've also milled PCBs, there are some benefits to milling, like you can drill holes at the same time. I think 2 sided PCBs are easier to mill than to etch. The limitation of milled (and etched at home) PCBs that I find most annoying is the lack of through-plated holes. This means you have to solder in wires, and solder to both sides of the board, for every via - it really adds some design limits and assembly time. Solder mask is another (optional) step, most people I know who make their own PCBs don't bother to use solder mask but it is available as UV-curable liquid.
Ordering PCBs is incredibly inexpensive these days. Oshpark is in the USA and a great place to get PCBs. There are places in China you can order from online like PCBway, I just priced out 5 PCBs of 100mm x 100mm, 2 layers, green solder mask, $5 + $20 shipping to Canada, delivery within a week.
Checking at a local hackerspace/makerspace is a great idea too, often there's people around who are making their own PCBs (or at least have in the past).
I've both etched (using the laser printer toner transfer method) and milled PCBs for through hole and surface mount parts, it was no problem etching a board for a TQFP 100 pin part (0.5mm pin spacing). I didn't push it further than that.
YouTube: [bbno$ - it boy (official music video)](https://www.youtube.com/watch?v=QuvqzlxEO6g) Watching the bbno$ video released today, "it boy", I realized (later than I'd like to admit) that it's shot in Cowichan, Vancouver Island. A lot of locations are recognizable in and around Duncan. When I saw bbno$ dancing on the boat, I finally clued in - that boat is beached at Cherry Point just down the road from my house! [I took photos of the same beached boat.](https://www.flickr.com/photos/chrisgerlinsky/53625600812/) "The Brazen Fork" is also shown in the video, a BBQ truck on Cowichan Bay Road (great food). The falcon landing was surely shot at [The Raptors](https://the-raptors.com) near Duncan. There are a lot of recognizable locations from the Cowichan area. And a great song! [bbno$ - it boy (official music video)](https://www.youtube.com/watch?v=QuvqzlxEO6g)
Mildly Interesting
I’m in a park. The grass is being mown by a robot.
akacastor 5 months ago • 83%
It's too bad that the first things to be automated are the tasks that people don't mind doing, leaving the real shitty tasks to be done by people. Riding around on a lawnmower has to be one of the most enjoyable forms of manual labour. Now the robots get the good jobs and we're left with the backbreaking monotonous bullshit.
akacastor 5 months ago • 100%
Thanks for calling the BBS, it's great finding and talking to so many other people who enjoy this!
Vintageakacastor 5 months ago • 100%
Fantastic! As soon as I saw the first photo I thought "what a wonderful play room!" and also I want to play in all the rest too. :)
akacastor 5 months ago • 100%
Where is this? What is this?
Beautiful desk and equipment!
akacastor 5 months ago • 100%
Thanks for checking it out! It's great being part of the BBS community again. So many bits to tinker with.
``` ------------------------ Another Millennium BBS ------------------------ * * * * * * * * * * * * GRAND OPENING * (still open * April 20, 2024 * other days!) * * * * * * * * * * * Canada: +1.587.67.31337 USA: +1.949.59.31337 telnet: another.tel ``` Running **Maximus** BBS software in MS-DOS for an authentic 90s BBS experience, with local and fsxNet message areas, file areas, and door games. **USRstats**, "modem stats" option on the main menu, provides information about your dialup modem connection to the BBS including baud rate and protocol information, error count, etc. **Buccaneer** door game - roam the sea, loot treasure ships, but beware the Spanish Armada! Players active daily. Astronomy Picture of the Day **SIXEL** format graphics in supporting terminals. (SyncTerm recommended) AP Class World HQ - hand-crafted artisinal cracks and keygens for special nearly-lost wares. Fast new user signup, real names not required. ***There's never been a better time to call a BBS!*** Check out a few of our own favourites in the "List of BBSes" at the main menu. ``` ======================= Another Millennium BBS ======================= Canada: +1.587.67.31337 USA: +1.949.59.31337 telnet: another.tel ======================= ``` Hope to see you online! Chris / akacastor (SysOp, Another Millennium BBS)
akacastor 5 months ago • 100%
For anyone interested in seeing SuperBBS - there is a BBS 'The Lower Planes' at tlp.zapto.org (BBS on port 6502) that claims to be the only SuperBBS in the world.
akacastor 5 months ago • 100%
Some other DOS BBS-related programs I cracked recently:
- Toilet Stall 1.0 graffiti door
- StickMan v1.11 (patched to remove requirement for numeric keypad, now playable on a laptop)
- Buccaneer 2.10 (found this game from original author's son's reddit post)
- Mission #2 Vacation In Hell! v2.01
- Blue Wave Mail Reader 2.30 DOS & 386
akacastor 5 months ago • 100%
I'm using IDA for disassembly and DOSBox-X for debugging, still kinda learning the ropes in 16-bit DOS disassembly but am finding the right tools actually work pretty well, at least in a lot of cases.
I looked at the 386 version (32 bit) of the Blue Wave mail reader and IDA did a great job of decompiling the key check function - I was very impressed - I was even able to copy and paste parts of the code from the decompilation into a keygen. Too bad IDA doesn't decompile 16-bit code - I may have to look into Ghidra sometime for that.
The MS-DOS debugger (DEBUG) is also surprisingly useful and powerful, considering its humble stature as 'some old thing in the DOS directory'. ;) Using the DOSBox-X debugger has advantages, but the simple DOS DEBUG utility was enough to figure out a couple keygens too.
cross-posted from: https://lemmy.world/post/14144651 > I've been getting into cracking DOS software, focusing on BBS software, doors, utilities, etc. My latest project is a keygen (registration # and key file generator) for SuperBBS 1.17-3. I understand that, like a lot of BBS software, the source code and registration tools for SuperBBS were lost to time. You can download SuperBBS 1.17-3 from Jason Scott's BBS Documentary website: http://software.bbsdocumentary.com/IBM/DOS/SUPERBBS/ > > The keygen 'SBBSKEY2.ZIP' is available for download in file area 4 (cracks) of Another Millennium BBS, another.tel port 23. > > ``` > ------------------------------------------------------------------------------- > SuperBBS 1.17-3 KEYGENv2 by akacastor 2024-04-10 > ------------------------------------------------------------------------------- > > The SBBS-KEY keygen will generate a registration number to enter in CONFIG and > a .SCC file that must be placed in the SBBS directory. > > > You _MUST_ do _BOTH_ of: > > 1) Enter Sysop Name, BBS Name, and Reg # under Registration in CONFIG. > > and > > 2) Place the generated .SCC file in your SBBS directory (where BBS.EXE lives). > > > The timestamp of the .SCC file cannot be altered! SuperBBS includes the .SCC > file timestamp in its verification checks. > > > ------------------------------------------------------------------------------- > > usage: SBBS-KEY "Sysop Name" "BBS Name" > > NOTE - don't forget the quotes around each name! > > ------------------------------------------------------------------------------- > > example: > > C:\CRACKS>SBBS-KEY "Sysop Name" "BBS Name" > > T H E @ ############ > @ @ #### ### > SuperBBS 1.17-3 @@@ ### #### > KEYGENv2 by akacastor 2024-04-10 @@ @@@@ @@ ### #### > @@@ @@ @@ ### ### > @@ @@@@ @@ ### #### > @@ @@ @ @@ ### ### > Place .SCC file in SBBS directory. @ @@ @@ @ ### #### > @ @@ @@ @@@@########## > NOTE: the .SCC file timestamp must @ @@ @@ @@@@@@ ### > not be changed! @ @@ @@@@@@ @ ### > @ @@ @@@@@@ @ #M# > @ @@@@@@ @@ @ #t# > Sysop: Sysop Name @@ @@@@ @@ @@ #M# > BBS: BBS Name @@@@@ @@@@ ### > Reg #: 37603203 @@@ @@@ @@ ### > @@@ @@ @@@@@@@@ @@@ ##### > SCC File: 917C5F7C.SCC @@ @@ ######### > SCC Date: 2024-04-10 00:54 @@ @@ > @ @ C L A S S > guess what... 1994, 2024, your shit's still getting cracked. > it's just now more of a philanthropic move instead of an anarchist one > > ------------------------------------------------------------------------------- > > ```
I've been getting into cracking DOS software, focusing on BBS software, doors, utilities, etc. My latest project is a keygen (registration # and key file generator) for SuperBBS 1.17-3. I understand that, like a lot of BBS software, the source code and registration tools for SuperBBS were lost to time. You can download SuperBBS 1.17-3 from Jason Scott's BBS Documentary website: http://software.bbsdocumentary.com/IBM/DOS/SUPERBBS/ The keygen 'SBBSKEY2.ZIP' is available for download in file area 4 (cracks) of Another Millennium BBS, another.tel port 23. ``` ------------------------------------------------------------------------------- SuperBBS 1.17-3 KEYGENv2 by akacastor 2024-04-10 ------------------------------------------------------------------------------- The SBBS-KEY keygen will generate a registration number to enter in CONFIG and a .SCC file that must be placed in the SBBS directory. You _MUST_ do _BOTH_ of: 1) Enter Sysop Name, BBS Name, and Reg # under Registration in CONFIG. and 2) Place the generated .SCC file in your SBBS directory (where BBS.EXE lives). The timestamp of the .SCC file cannot be altered! SuperBBS includes the .SCC file timestamp in its verification checks. ------------------------------------------------------------------------------- usage: SBBS-KEY "Sysop Name" "BBS Name" NOTE - don't forget the quotes around each name! ------------------------------------------------------------------------------- example: C:\CRACKS>SBBS-KEY "Sysop Name" "BBS Name" T H E @ ############ @ @ #### ### SuperBBS 1.17-3 @@@ ### #### KEYGENv2 by akacastor 2024-04-10 @@ @@@@ @@ ### #### @@@ @@ @@ ### ### @@ @@@@ @@ ### #### @@ @@ @ @@ ### ### Place .SCC file in SBBS directory. @ @@ @@ @ ### #### @ @@ @@ @@@@########## NOTE: the .SCC file timestamp must @ @@ @@ @@@@@@ ### not be changed! @ @@ @@@@@@ @ ### @ @@ @@@@@@ @ #M# @ @@@@@@ @@ @ #t# Sysop: Sysop Name @@ @@@@ @@ @@ #M# BBS: BBS Name @@@@@ @@@@ ### Reg #: 37603203 @@@ @@@ @@ ### @@@ @@ @@@@@@@@ @@@ ##### SCC File: 917C5F7C.SCC @@ @@ ######### SCC Date: 2024-04-10 00:54 @@ @@ @ @ C L A S S guess what... 1994, 2024, your shit's still getting cracked. it's just now more of a philanthropic move instead of an anarchist one ------------------------------------------------------------------------------- ```
Ask Electronics
Making a PCB, using solder mask as etch resist.
akacastor 6 months ago • 100%
Adding solder mask is an optional step. If you use an etch resist like toner or dry film, you have a functional PCB even without solder mask. The solder mask is the unnecessary step that can be skipped.
Using solder mask as an etch resist, you would have to scrape away the remaining mask in areas where you want exposed pads - you would either need another mask for this, or to manually scrape each pad, adding an unnecessary step.
akacastor 6 months ago • 100%
Sounds like a great time, awesome to play a game to maximize the fun! Gonna have to keep an eye out for an active Exitilus game!
RetroGaming
Should I get an NES, Master System; or an Atari 7800?
akacastor 6 months ago • 100%
Speaking of Contra - there is a new Contra out March 12, 2024 (today! or tomorrow depending on timezone), Contra: Operation Galuga. I haven't played the game yet, but the trailer looks amazing!
akacastor 6 months ago • 100%
I haven't played Exitilus, searching just now I see The Realm of Serion BBS has it, sounds like fun! Right now I am just a few days into my first game of LORD, after saying "maybe I'll play a game of that someday" since the 1990s. :)
akacastor 6 months ago • 100%
I am not very familiar with the A800 but there are a lot of wifi networking adapters and the such these days for all kinds of systems, many of them emulate modems so they are well-suited to interfacing with a BBS. "RS-232 wifi modem" as search terms gives a bunch of options.
Also useful for old computers: http://theoldnet.com/ provides ways to use computers from the 1990s online today to access some websites etc.
akacastor 6 months ago • 100%
A list of over 1,000 (current) BBSes: https://www.telnetbbsguide.com
Most of these BBSes are accessible via telnet - there are many options for telnet, but typically for BBSes you want a terminal that supports ANSI colours and IBM-PC characters (CP437). A recommended terminal program for Win/Mac/Linux is SyncTerm: https://syncterm.bbsdev.net
There are about 40 dialup modem BBSes in the list: https://www.telnetbbsguide.com/bbs/connection/dial-up/
For more information about the world of BBSes in the 1980s and 90s, a great source of history is Jason Scott's BBS Documentary and Al's Geek Lab Back to the BBS.
www.southernamis.com
**IT'S BAUD DAY 3/12/24** *From the linked site:* Something that SysOps did when they advertised their BBS. Rather than write a BBS’ supported baud rates as “300/1200/2400”, they would write “3/12/24”. The reason for this abbreviation is probably due to how BBSs were advertised back in the day. Most BBSs were advertised in text files. Depending on the host computer, a text file may have 40 or 80 characters per line. So, space was a premium and dropping 6 characters from “300/1200/2400” made a big difference.
Piracy: ꜱᴀɪʟ ᴛʜᴇ ʜɪɢʜ ꜱᴇᴀꜱ
Saving a Buccaneer
akacastor 7 months ago • 100%
Some 'getting started' suggestions:
Telnet BBS Guide has over a thousand BBSes listed, most are accessible by telnet. Syncterm is a great terminal program for BBS use, with Linux/Mac/Windows versions available. Other telnet clients can be used, but many BBSes use ANSI and CP437 and not UTF8. (other BBSes use other standards like ATASCII or PETSCII, Syncterm supports many of these.)
There are a bunch of interesting BBSes, one I'd recommend is 20 For Beers, connect to it at 20forbeers.com:1337. Plenty of great ANSI art and active message areas and a huge file collection too. I also recommend checking out the fsxNet message areas, they are shared across many BBSes and have an active community.
Piracy: ꜱᴀɪʟ ᴛʜᴇ ʜɪɢʜ ꜱᴇᴀꜱ
Saving a Buccaneer
akacastor 7 months ago • 100%
This is so cool to see posted here! I'm the guy that broke my usual don't-post-on-reddit rule to share a keygen for Buccaneer. It really is a fun game, too, even if it can be a bit brutal (this is the third day in a row my ship got sunk!).
There continues to be a thriving community of BBS users and sysops, there is a mix of new software and mods along with the old (there are CBBS systems operating - that is the original BBS software created in the late 1970s!). The fsxNet echomail network is great, linking a lot of active BBSes together and with good conversation and lots of help for retro-tech issues and projects.
If you're interested in playing Buccaneer online, The Fool's Quarter BBS has the game online. Another interesting BBS to check out is 20 For Beers reachable via telnet at 20forbeers.com:1337.
akacastor 8 months ago • 33%
Thank you for this learning experience, before now I was not aware of weather. Continue your valuable contributions.
akacastor 8 months ago • 50%
Nobody dare making a comment on the internet without taking Winnipeg into account!!
picsakacastor 9 months ago • 100%
Clever photo, great idea. The "flame" effect is brilliant. Thanks for sharing!
British Columbia
PPC Candidate lied.
akacastor 9 months ago • 100%
Although to many of us who aren't engineers, some of the rules may not be obvious and it may look like an honest oversight - if you know any engineers, they have these rules absolutely drilled into them by the time they've earned a degree.
For someone with no engineering background to make a mistake like this is easy to explain. When someone with an engineering degree does it - they absolutely did know what they were doing is against professional regulations.
David Hilderman is a liar.
akacastor 10 months ago • 100%
I like this, the tilted camera adds a "fun" aspect, the low perspective captures the bird well, pretty colours in the background, the softness of the background is great as well, nice separation of foreground and background without destroying the background. Also, the bird is not smoking, so it is nice to see it following the rules. Good balance of chaos and rules. Thanks for sharing.
RetroGaming
The Beverly Hillbillies [MS DOS] Some Music on Roland MT-32
akacastor 10 months ago • 100%
The animation with the C:\ prompt is great! I hadn't seen this before, but that's one of the all-time greatest game openings!
akacastor 10 months ago • 100%
Very nice composition, the lines of the guard rail and of the highway trailing into the distance, the balance of the sky and the ground, mysterious beauty of the fog, the glowing sun, I really like it all. The bare trees in the near-distant fog are wonderful too.
Thank you for sharing.
Ask Electronics
At what size of transistor does semiconductor manufacturing become practical for independent manufacture?
akacastor 11 months ago • 100%
Sam Zeloof (http://sam.zeloof.xyz/) has been working in the area of DIY semiconductor fabrication, and has successfully fabricated working ICs (from 6 - 100 transistors). He's done an incredible job at reaching ~1970's technology levels in a home lab.
Another example of DIY fabrication: https://hackaday.com/2010/03/10/jeri-makes-integrated-circuits/ Jeri Ellsworth made her own silicon inverter.
These examples are still very small-scale compared to even simple microprocessors, etc - but it's fascinating to see this level of technology becoming more accessible.
The window sill has plenty of space and is a cozy spot, directly above the baseboard heater in the space behind the couch. This is one of her favourite spots.
cross-posted from: https://lemmy.world/post/6135073 > Photo of a sea lion enjoying the sun on a dock in the marina at Cowichan Bay, Vancouver Island. > > Sea lions visit Cowichan Bay in the fall to feast on salmon on their way to migrate upstream. It is early in the season, many more sea lions will arrive this month. [Read more here.](https://www.cowichanestuary.ca/sea-lion/) > >  > >  > > 
cross-posted from: https://lemmy.world/post/6135073 > Photo of a sea lion enjoying the sun on a dock in the marina at Cowichan Bay, Vancouver Island. > > Sea lions visit Cowichan Bay in the fall to feast on salmon on their way to migrate upstream. It is early in the season, many more sea lions will arrive this month. [Read more here.](https://www.cowichanestuary.ca/sea-lion/) > >  > >  > > 
cross-posted from: https://lemmy.world/post/6135073 > Photo of a sea lion enjoying the sun on a dock in the marina at Cowichan Bay, Vancouver Island. > > Sea lions visit Cowichan Bay in the fall to feast on salmon on their way to migrate upstream. It is early in the season, many more sea lions will arrive this month. [Read more here.](https://www.cowichanestuary.ca/sea-lion/) > >  > >  > > 
Photo of a sea lion enjoying the sun on a dock in the marina at Cowichan Bay, Vancouver Island. Sea lions visit Cowichan Bay in the fall to feast on salmon on their way to migrate upstream. It is early in the season, many more sea lions will arrive this month. [Read more here.](https://www.cowichanestuary.ca/sea-lion/)   
cross-posted from: https://lemmy.world/post/5560795 > Aboard BC Ferries vessel Coastal Celebration travelling from Tsawassen (Vancouver) to Swartz Bay (Victoria), September 21 2023.
cross-posted from: https://lemmy.world/post/5560795 > Aboard BC Ferries vessel Coastal Celebration travelling from Tsawassen (Vancouver) to Swartz Bay (Victoria), September 21 2023.
cross-posted from: https://lemmy.world/post/5560795 > Aboard BC Ferries vessel Coastal Celebration travelling from Tsawassen (Vancouver) to Swartz Bay (Victoria), September 21 2023.
Aboard BC Ferries vessel Coastal Celebration travelling from Tsawassen (Vancouver) to Swartz Bay (Victoria), September 21 2023.
cross-posted from: https://lemmy.world/post/5086078 > View from Split Rock Lookout on the Malahat, Cowichan, Vancouver Island, looking east at Saanich peninsula with Mt. Baker in the background, Sep 14 2023.
cross-posted from: https://lemmy.world/post/5086078 > View from Split Rock Lookout on the Malahat, Cowichan, Vancouver Island, looking east at Saanich peninsula with Mt. Baker in the background, Sep 14 2023.
cross-posted from: https://lemmy.world/post/5086078 > View from Split Rock Lookout on the Malahat, Cowichan, Vancouver Island, looking east at Saanich peninsula with Mt. Baker in the background, Sep 14 2023.
View from Split Rock Lookout on the Malahat, Cowichan, Vancouver Island, looking east at Saanich peninsula with Mt. Baker in the background, Sep 14 2023.
akacastor 1 year ago • 100%
Thanks for the critique! To be honest, most of the composition was based on luck for me - I saw the artwork on the concrete wall and its position on the beach is perfect - really the artist who painted the wall deserves the most credit. I did position the art to the left side (rule of thirds), I felt that showing a bit more space gave more "on the beach" feeling. I aligned the sand with the bottom third and then the concrete slab being proportioned equally was serendipity.
cross-posted from: https://lemmy.world/post/4840439 > Art on the beach at Maffeo Sutton Park in Nanaimo, BC, Canada, September 2023.
Art on the beach at Maffeo Sutton Park in Nanaimo, BC, Canada, September 2023.
Canada
Announcing the winners of the 2023 Canadian Wildlife Photography of the Year competition
akacastor 1 year ago • 100%
One of the photographers mentioned is Simon d'Entremont from Nova Scotia.
Simon d'Entremont has an excellent YouTube channel where he shares photography tips and techniques. As I've started learning about photography, Simon's videos are the resource I have gained most from. I can't recommend them enough to anyone learning or growing photography skills.
>[Cobble Hill] will be hosting our traditional Fair on Saturday, August 26th and have a wonderful day of entertainment planned for you. > >This will be the 114th edition of the Cobble Hill Fair and it will be our traditional event. After 2 years of hosting 'virtual' events, we know the community is looking forward to seeing neighbours and friends, both old and new, at this great family event.
www.flickr.com
The [Bulls, Broncs & Barrels event](https://www.viwesternheritage.com/) was held at the Coombs, BC, rodeo grounds the weekend of August 19-20, 2023. Great turnout and even better riders! [My (amateur) photo album on flickr.](https://www.flickr.com/gp/chrisgerlinsky/44T31949Q7)
www.flickr.com
The 151st Chilliwack Fair was held August 11-13, 2023. There was a lot going on - a large exhibition of livestock, farm equipment from the present and past, many food trucks, motocross stunts, live music, a full rodeo and more. The linked [flickr album](https://www.flickr.com/gp/chrisgerlinsky/e4J2yK0R6i) has my amateur photos from the weekend (Friday and Saturday).
flic.kr
cross-posted from: https://lemmy.world/post/2836368 > The Cow Bay Regatta 2023 took place in Cowichan Bay, Vancouver Island, BC the weekend of August 5-6th. https://www.cowbay-regatta.ca/ > > The linked [flickr album](https://flic.kr/s/aHBqjAQdsk) has my amateur photos, taken Saturday morning at Cherry Point beach. Shot on a Sony a7iv w/Sigma 100-400mm lens. []()
flic.kr
The Cow Bay Regatta 2023 took place in Cowichan Bay, Vancouver Island, BC the weekend of August 5-6th. https://www.cowbay-regatta.ca/ The linked [flickr album](https://flic.kr/s/aHBqjAQdsk) has my amateur photos, taken Saturday morning at Cherry Point beach. Shot on a Sony a7iv w/Sigma 100-400mm lens. []()